View MP2030DQ_8937504.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mp2030 3a dual supply very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 1 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. the future of analog ic technology description the mp2030 is a very low dropout, dual supply linear regulator. the use of two supplies allows the bias to control an nmos device. the nmos device supplies power to the load via the in. in this way the input supply can be just above the desired output, yet still provide very good regulation performance due to the higher bias supply. the bias operates from a 2.5v to 5.5v input and regulates the output voltage to as low as 0.9v, and as high as 3.8v. the mp2030 can supply up to 3a of load current with a typical dropout voltage of 150mv. the bias runs the internal reference and drive circuitry, while the output current comes directly from the in for high efficiency regulation. the low bias current of 220ua makes the mp2030 ideal for use in battery-powered applications. the bias can be directly applied from the battery while in is powered from the high efficiency buck regulator. this will reduce the output noise and decoupling capacitor. other features of mp2030 include thermal overload and current limit protection, power good indicator, stability with ultra low esr ceramic capacitors as low as 1uf, and fast transient response. the mp2030 is available in 10-pin qfn (3mm x 3mm), and in qfn (5mm x 5mm) packages. features ? wide 1.1v to 5.5v input voltage range ? stable with very small ceramic capacitors ? 150mv dropout at 3a output ? 2% accurate output voltage ? adjustable output range of 0.9v to 3.8v ? low noise: 80v rms (10hz to 100khz) ? psrr o 32db at 100khz ? better than 0.001%/ma load regulation ? stable with low-esr output capacitors ? low 220ua ground current ? internal thermal protection ? current limit protection ? 0.1a typical quiescent current at shutdown ? power good indicator applications ? network, telecom, equipment: routers and switches ? servers, storage equipment ? set-top box ? post regulation for switch mode ? televisions ?mps? and ?the future of analog ic technology? are registered trademarks of monolithic power systems, inc. typical application c6 10nf u1 in out out fb en bp in bias pg gnd mp2030 5 3 1 8 9 6 10 7 2 4 vin bias pgood gnd en c8 1nf gnd vout 1.8v/3a
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 2 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. ordering information part number* package top marking free air temperature (t a ) MP2030DQ * 3x3 qfn10 7d ?40 c to +85 c mp2030du * * 5x5 qfn32 m2030du ?40 c to +85 c * for tape & reel, add suffix ?z (eg. MP2030DQ?z). for rohs compliant packaging, add suffix ?lf (eg. MP2030DQ?lf?z) ** for tape & reel, add suffix ?z (eg. mp2030du?z). for rohs compliant packaging, add suffix ?lf (eg. mp2030du?lf?z) package reference top view vin vin bias pgood gnd 1 2 3 4 5 vout vout fb en bypass 10 9 8 7 6 exposed pad on backside 3x3 qfn10 absolute maxi mum ratings (1) v bias , v in to gnd............................?0.3v to +6v fb, en, to gnd ..............................?0.3v to 6v v out ...............................?0.3v to v in + 0.3 or 6v pgood ..................... ?0.3v to v bias + 0.3 or 6v bypass ......................-0.3v to v bias +0.3 or 6v junction temperature ...............................150 c lead temperature ....................................260 c storage temperature ............. ?65c to +150 c power dissipation t a =70 c (qfn10 3 x 3) ............................ 1.3w t a =70 c (qfn32 5 x 5) ............................. 1.8w top view 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 n/c vin vin vin vin bias pgood gnd n/c vout vout vout vout fb en bypass n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c n/c 9101112131415 16 32 31 30 29 28 27 26 25 exposed pad on backside 5x5 qfn32 recommended operating conditions (2) input voltage v in ............................. 1.1v to 5.5v input voltage v bias .......................... 2.5v to 5.5v output voltage................................ 0.9v to 3.6v load current............................... 3.0a maximum operating junct. temp. ...........?40 c to +125 c thermal resistance (3) ja jc qfn10 3x3? ......................... 50??12 c/w qfn32 5x5? ......................... 36?.?8 c/w notes: 1) exceeding these ratings may damage the device. 2) the device is not guaranteed to function outside of its operating conditions. 3) measured on jesd51-7, 4-layer pcb.
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 3 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. electrical characteristics v in = 1.5v, v bias = 3.6v, v out = 1.2v, c out = 1f, c in = 0.1f, t a = +25 c, unless otherwise noted. parameter symbol condition min typ max units v in operating voltage 1.1 5.5 v v bias operating voltage 2.5 5.5 v v bias operating current 220 a 0.490 0.500 0.510 fb regulation voltage ?40 c t a +85 c 0.485 0.500 0.515 v dropout voltage i out = 3a, v bias = 3.6v 150 mv v in line regulation i out = 1ma, v in = 1.5 to 5v v bias = 3.6v v out = 1.2v 1 mv v bias line regulation i out = 1ma, v bias = 3.6v to 5.5v v out = 1.2v v in = 1.5v 2 mv load regulation i out = 1ma to 1a 0.001 %/ma psrr (v in ) v in > v out + 0.5v, c out = 22 f, v in (ac) = 100mv, f = 100khz i out = 300ma 32 db power good threshold 440 mv power good delay 160 s soft start bypass=open 550 s power good voltage i sink =230 a 0.39 v en input high voltage 1.5 v en input low voltage 0.8 v en input bias current v en = 1.2v ?1 +1 a thermal protection 135 c thermal protection hysteresis 15 c
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 4 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. pin functions qfn3x3 10pins pin # name description 9, 10 out regulator output. out is the output of the li near regulator, by pass out to gnd with a 4.7f or greater capacitor. 3 bias bias voltage. bypass to ground with a 1uf or greater capacitor for maximum output current the vin>0.2v+v out and vbias>2v+vout. 8 fb feedback input. connect a resistive voltage divider from out to fb to set the output voltage. out feedback threshold is 0.5v. 7 en enable input. drive en high to turn on the mp2030, drive en low to turn it off. for automatic startup, connect en to in. 5 gnd ground, exposed pad. 1, 2 in power source input. in supplies power to the load at the output (through the power transistor). bypass in to gnd with a 1f or greater capacitor. 4 pgood open drain output. high indicated v out > 90% final value. 6 bypass connect a 1nf to this pin. do not load this pin resistively. qfn5x5 32pins pin # name description 20, 21,22, 23 vout regulator output. out is the output of the li near regulator, by pass out to gnd with a 4.7f or greater capacitor. 6 bias bias voltage. bypass to ground with a 1uf or greater capacitor. 19 fb feedback input. connect a resistive voltage divider from out to fb to set the output voltage. out feedback threshold is 0.5v. 18 en enable input. drive en high to turn on the mp 2030, drive en low to turn it off. for automatic startup, connect en to in. 8 gnd ground, exposed pad. 2, 3, 4, 5 vin power source input. in supplies power to the load at the output (through the power transistor). bypass in to gnd with a 1f or greater capacitor. 7 pgood open drain output. high indicated v out > 90% final value. 17 bypass connect a 1nf to this pin. do not load this pin resistively. 1, 9, 10, 11, 12, 13, 14, 15, 16, 24, 25, 26, 27, 28, 29, 30, 31, 32 nc these are no connection pins.
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 5 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. typical performanc e characteristics c1=10 f, c2=0.1 f, c3=1.0 f, c4=22 f, c6=22nf, v b =5.5v, t a =25oc, unless otherwise noted . voltage dropped psrr vs. frequency case temperature vs. p d mp2030du line regulation line regulation line regulation 0 50 100 150 200 0.0 0.8 1.6 2.4 3.2 4.0 load current ( a ) voltage dropped ( mv ) v b =5v v out =1.2v 1.210 1.214 1.218 1.222 1.226 1.230 1.5 2.0 2.5 3.0 3.5 4.0 4.5 v in ( v ) v in ( v ) v in ( v ) v out ( v ) v out ( v ) v out ( v ) v out ( v ) v out ( v ) v out ( v ) 0a 0.4a 1.2a 1.2a 0a 0.4a load regulation load regulation load regulation 1.20 1.21 1.22 1.23 1.24 1.25 0.0 0.6 1.2 1.8 2.4 3.0 3.6 i out (a) i out (a) i out (a) v in =1. 5v v in =1. 8v 0 10 20 30 40 50 60 70 80 90 0.01 0.1 1 10 100 1000 frequency ( khz ) psrr ( db ) 1.800 1.804 1.808 1.812 1.816 1.820 2.0 2.5 3.0 3.5 4.0 4.5 1.800 1.804 1.808 1.812 1.816 1.820 0.0 0.6 1.2 1.8 2.4 3.0 3.6 v in =2.1v v in =2.5v 20 30 40 50 60 70 80 0.5 1.0 1.5 2.0 2.5 3.0 p d ( w ) v out =1.2v v b =5v 2.50 2.50 2.51 2.51 2.52 2.52 2.5 2.9 3.3 3.7 4.1 4.5 0a 1.2a 0.4a 2.500 2.504 2.508 2.512 2.516 2.520 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v in =2.8v v in =3.3v v in =1.5v v out =1.2v i out =0.3a
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 6 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. typical performanc e characteristics c1=10 f, c2=0.1 f, c3=1.0 f, c4=22 f, c6=22nf, v b =5.5v, t a =25oc, unless otherwise noted v dropout vs. temperature v out =1.2v, i out =1a vout vs. temperature v in =1.5v, v out =1.2v, i out =1ma v fb vs. temperature v out ( v ) 25 28 31 34 37 40 -45 -25 -5 15 35 55 75 95 v dropout ( mv ) i out =1a 0.490 0.495 0.500 0.505 0.510 0.515 0.520 -45 -25 -5 15 35 55 75 95 v fb ( v ) 1.18 1.19 1.20 1.21 1.22 1.23 -45 -25 -5 15 35 55 75 95 v in 2v/div v en 2v/div v out 1v/div v out 0.1v/div i out 0.5a/div v in 2v/div v in 2v/div v pg 5v/div v en 2v/div v out 1v/div v out 1v/div i out 0.5a/div i out 2a/div i out 1a/div v out 2v/div i out 5a/div v out 2v/div i out 5a/div
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 7 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. typical performanc e characteristics c1=10 f, c2=0.1 f, c3=1.0 f, c4=22 f, c6=22nf, v b =5.5v, t a =25oc, unless otherwise noted power rump up v in =2.1v, v out =1.8v, i out =3a, with resistor load power rump down v in =2.1v, v out =1.8v, i out =3a, with resistor load line transient v in =1.8 to 5v, v out =1.2v, i out =0.2a, v in 2v/div v b 5v/div v out 1v/div v in 2v/div v out 20mv/div i out 2a/div v in 2v/div v b 5v/div v out 1v/div i out 2a/div
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 8 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. block diagram bypass bias en gnd pgood o fb vout vin + -- + -- 0.5v 0.45v reference soft start gate turns off the gate 160us delay -- + figure 1?block diagram of low dropout regulator
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 9 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. operation mp2030 theory of operation the mp2030 linear dropout regulator provides adjustable output voltages from 0.9v to 3.6v at currents up to 3a. this ldo is protected against short circuits, and it has thermal shut down protection with 15 o c hystheresis. utilizing two power supplies in order to maximize the efficiency mp2030 uses two power supplies. one power supply is connected to the bias pin and it is used to power up the internal circuitries including band gap reference and the rest of control circuitries. the other power supply is connected to the vin pins which are the drain of pass device. this power supply can be set close to output voltage of ldo. the output pins are the source of the pass device. the smaller voltage drop across the pass device translates to the smaller power loss in pass device. thus, the part operates with higher efficiency. internal current limit the mp2030 has an internal current limit set at almost 4.5a. when the output current is greater than 4.5a, current limit is activated, the output voltage is internally forced close to ground, and stays at this voltage until the short circuit is removed. internal current limit is very well controlled over process variations and ambient temperature. enable the enable (en) pin is active high. the enable pin has a built-in hystheresis. if this pin is held below 0.8v then part shuts down and draws less than 1ua from v bias supply. if not used then connect this pin to v bias . under voltage lockout the bias voltage is monitored by a circuit that prevents the ldo start up when the bias voltage is below 2.35v. this circuitry has an approximate hystheresis of 90mv. soft start mp2030 incorporates internal soft start function. this internal function reduces the start up current surge into the output capacitor. this allows the gradual built up of output voltage to its final set value. the internal soft start cap is held to ground if there is a fault condition. the fault conditions are uvlo, thermal shut down, and disable. the internal soft start time is almost 550us. power good the power good pin is an open drain output and can be connected to bias voltage via a pull up resistor. open drain transistor turns off and pg pin voltage value becomes v bias when v fb exceeds 450mv. also pg pin can sink at least 230 a while being low. setting the output voltage the mp2030 has an adjustable output voltage, set by using a resistive voltage divider from the output voltage to fb pin. the voltage divider divides the output voltage down to the feedback voltage by the ratio: v fb = v out *r 2 / (r 1 +r 2 ) where v fb is the feedback threshold voltage (v fb =0.5v), and v out is the output voltage. r 1 connects between v out and v fb , and r 2 connects between v fb and ground. thus the output voltage is: v out = 0.5*(r 1 +r 2 )/r 2 r 2 can be as high as 100k , but a typical value is 10k . using that value, r 1 is determined by: r 1 =r 2 x (v out -v fb )/v fb for example, for a 1.8v output voltage, r 2 is 10k , and r 1 is 26k . you can select 26k (1%) resistor for r 1 . power dissipation most of the power dissipation is due to power dissipation in pass device. for example, assume v bias =5.0v, v in =2.0v, v out =1.8v, and i out =3a: p d ( pass ) = (v in -v out ) x i out p d ( pass ) = (2.0v-1.8v) x 3a=0.6
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 10 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. p bias = v bias x i gnd = 5v x (220ua) = 1.25mw. this is negligible compared to p d ( pass ) =0.6w for qfn 3x3 ja is 50 o c/w. 0.6w power is dissipated when 3a output current goes through pass device with v in =2.0v, and v out =1.8v. this gives a rise in die temperature for 0.6 x 50 o c/w=30 o c this is a safe operating point assuming a junction temperature of 135 o c at an 85 o c ambient temperature. a heat sink needs to be utilized for a better temperature performance.
mp2030 ? 3a very low dropout linear regulator mp2030 rev. 0.91 www.monolithicpower.com 11 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. package information qfn10 (3mm x 3mm) side view top view 1 10 6 5 bottom view 2.90 3.10 1.45 1.75 2.90 3.10 2.25 2.55 0.50 bsc 0.18 0.30 0.80 1.00 0.00 0.05 0.20 ref pin 1 id marking 1.70 0.50 0.25 recommended land pattern 2.90 note: 1) all dimensions are in millimeters. 2) exposed paddle size does not include mold flash. 3) lead coplanarity shall be 0.10 millimeter max. 4) drawing conforms to jedec mo-229, variation veed-5. 5) drawing is not to scale. pin 1 id see detail a 2.50 0.70 pin 1 id option b r0.20 typ. pin 1 id option a r0.20 typ. detail a 0.30 0.50 pin 1 id index area
mp2030 ? 3a very low dropout linear regulator notice: the information in this document is subject to change wi thout notice. please contact m ps for current specifications. users should warrant and guarantee that third party intellectual property rights ar e not infringed upon when integrating mps products into any application. mps will not assume any legal responsibility for any said applications. mp2030 rev. 0.91 www.monolithicpower.com 12 10/10/2011 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. qfn32 (5mm x 5mm)

▲Up To Search▲

Price & Availability of MP2030DQ

	To Download MP2030DQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .